Https://www.driverscape.com/download/usb-serial-ch340
Usb To Serial Driver For Windows 10
Usb To Serial 340 Driver
Usb Serial Ch340 Com3 Win 10 Drivers
Download Usb-serial Ch340 Driver Windows 10
Driver Scape Download Usb Serial Ch340

Download drivers for CH340 IC for windows 7, windows 8, windows 10 and also for MAC users. Check out how to install drivers for Arduino UNO, NODE MCU and Arduino Nano which have ch340g usb to serial converter IC. To look for CH340 driver files (i.e. Usb.kext or usbserial.kext) in the path, you could use the following command. Ls grep usb You should see something similar to the output below after using the commands. If you have found the file in the path, you will need to run each of the following commands in the CLI/Terminal to remove old CH340 drivers. Use the USB / Serial CH340 / CH341 Driver‘s Download: Windows 32 bit: Download. Windows 64 bit: Download. Linux: Download. USB Serial Driver CH 340 can be used for Windows XP / Win 7 / Wind 8. I try to use Windows 8. If USB Serial Drivers are successful it will be visible in the Devices Manager of Windows. Hello I need to install (remotely) a driver 'USB-SERIAL CH340' to allow an Arduino board to communicate with a PC. This driver is used as a serial port over a USB port. Since we are all confined ( Covid-19), I can't go to his place to help him. Driver description Download driver USB-SERIAL CH340 version 3.4.2014.08 for Windows XP, Windows Vista, Windows 7, Windows 8, Windows 8.1, Windows 10 32-bit (x86), 64-bit (x64).

The CH340 chip is used by a number of Arduino compatible boards to provide USB connectivity, you may need to install a driver, don’t panic, it’s easier than falling off a log, and much less painful.

Windows

(Manufacturer’s Chinese Info Link)

Download the Windows CH340 Driver
Unzip the file
Run the installer which you unzipped
In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Older Windows Driver Version and Instructions

~~Download the Windows CH340 Driver~~
~~Unzip the folder.~~
If you are running a 64Bit Windows: – run the SETUP_64.EXE installer.
If you are running a 32Bit Windows: – run the SETUP_32.EXE installer.
~~If you don’t know, try the 64 bit and if it doesn’t work, the 32 bit.~~
~~In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.~~

Macintosh

(Manufacturer’s Chinese Info Link)

The following github has up to day pkg files for 1.3, 1.4 and 1.5 at time of writing, thanks to Joshua Wallis for bringing this to my attention…

Direct Download Links (from the github repo above):

Https://www.driverscape.com/download/usb-serial-ch340

See the github link above for installation instructions if you need them.

Previous macinstosh downloads if the above doesn’t work for you…

~~(V1.3) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11) and Sierra (10.12)~~

~~Inside the zip file you will find a PDF and a “pkg” file, short version, double click the pkg file, the PDF has some extra information.~~

~~OSX Sierra (10.12) Note~~

~~A kindly user, Maarten Segers reports~~

~~FYI, the driver documented here WILL crash on OSX Sierra.~~

~~Make sure to use this one instead: https://github.com/MPParsley/ch340g-ch34g-ch34x-mac-os-x-driver~~

~~I can personally not test on MacOS and can not vouch for the above drivers at github, but there you go.~~

Usb To Serial Driver For Windows 10

~~See uninstalling information at the bottom of the page if the driver causes problems for you.~~

~~Here is an older version of the Mac driver, NOT FOR 10.12 Sierra~~

~~(V1.0) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11)~~

Usb To Serial 340 Driver

Linux

(Manufacturer’s Chinese Info Link)

Drivers are almost certainly built into your Linux kernel already and it will probably just work as soon as you plug it in. If not you can download the Linux CH340 Driver (but I’d recommend just upgrading your Linux install so that you get the “built in” one).

Uninstalling From Macinstosh

A couple of Mac users have said “the driver crashes my mac Sierra how do I uninstall”.

Firstly regards the crash make sure you installed the 1.3 version of the driver, not the old one. You could download it directly from the Manufacturers Website in case they have issued an update since I wrote this page.

Usb Serial Ch340 Com3 Win 10 Drivers

Download Usb-serial Ch340 Driver Windows 10

Secondly a quick google search reveals that this is how you uninstall:

Driver Scape Download Usb Serial Ch340

Open a terminal and type: cd /Library/Extensions/
Verify that the .kext file is present: ls | grep usbserial.kext
Output should be: usbserial.kext
Then type: sudo rm -R usbserial.kext
Verify that the .kext file has been removed: ls | grep usbserial.kext
Output should be empty.
After you should remove the files stored in receipts folder: cd /private/var/db/receipts/
Find the enties: ls | grep usbserial*
Output should be: codebender.cc.ch34xinstaller.usbserial.pkg.bom codebender.cc.ch34xinstaller.usbserial.pkg.plist
Remove each one of the files of the above list: sudo rm -r filename`